[分享]TP-Link TL-WR703N 改64M RAM和8M FLASH

2013年后生产的版本都过渡到1.7了，虽然标签上还是1.6版本，与1.6版本相比，区别在于几个零件的变化，PCB颜色加深。其他没变，皆为AR9331+32M+4M的搭配。

本次DIY需要改动的地方：

1.将32M内存改为64M
2.更换8M FLASH
3.将TTL与MicroUSB连接
4.改刷OpenWRT固件

工具就一把老的电烙铁。上了年纪的。

拆开后，电路板正反面拍一张

正面

反面

① 拆下32M DDR400内存颗粒，改为64M。我使用的是 HY5DU121622CTP-D43 颗粒。

HY5DU121622CTP-D43内存颗粒

拆下内存

清理掉松香残留

放大一张看看

更换好内存

检查下是否有虚焊

全图

② 更换8M FLASH

拆下原装的4m flash

更换上一颗WinBond W25Q64CVSIG 容量 8M，已烧录好703的编程器固件

③连接TTL至MicroUSB

电烙铁的头太大了，连接USB难度好高，而且也没找到系的线，，只能弄这找到的最细的线替代了。。

插电，测试。TTL输出：

U-Boot 1.1.4 (Dec 4 2012 – 11:19:40)

AP121 (ar9330) U-boot

DRAM: 64 MB
led turning on for 1s…
id read 0x100000ff
flash size 4194304, sector count = 64
Flash: 4 MB
Using default environment

In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize…
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:7f:09:0b:ad
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
Autobooting in 1 seconds
## Booting image at 9f020000 …
Uncompressing Kernel Image … OK

Starting kernel …

Booting AR9330(Hornet)…
Linux version 2.6.31–LSDK-9.2.0.312 (root@localhost.localdomain) (gcc version 4.3.3 (GCC) ) #68 Tue Dec 4 11:19:54 CST 2012
flash_size passed from bootloader = 4
CPU revision is: 00019374 (MIPS 24Kc)
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
User-defined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Zone PFN ranges:
Normal 0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ar7240-nor0:128k(u-boot),1024k(kernel),2816(rootfs),64k(config),64k(ART) mem=32M
PID hash table entries: 128 (order: 7, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 29880k/32768k available (1883k kernel code, 2888k reserved, 521k data, 112k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
plat_time_init: plat time init done
Calibrating delay loop… 266.24 BogoMIPS (lpj=532480)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
===== ar7240_platform_init: 0
Whoops! This kernel is for product wr703 v1.0!

bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
AR7240 GPIOC major 0
squashfs: version 4.0 (2009/01/31) Phillip Lougher
NTFS driver 2.1.29 [Flags: R/O].
msgmni has been set to 58
alg: No test for lzma (lzma-generic)
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
ttyS0: detected caps 00000000 should be 00000100
serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A
console [ttyS0] enabled
PPP generic driver version 2.4.2
NET: Registered protocol family 24
cmdlinepart partition parsing not available
set partition boot
set partition kernel
set partition rootfs
set partition config
set partition art
Searching for RedBoot partition table
5 RedBoot partitions found on MTD device ar7240-nor0
Creating 5 MTD partitions on “ar7240-nor0”:
0x000000000000-0x000000020000 : “boot”
0x000000020000-0x000000120000 : “kernel”
0x000000120000-0x0000003e0000 : “rootfs”
0x0000003e0000-0x0000003f0000 : “config”
0x0000003f0000-0x000000400000 : “art”
->Oops: flash id 0xef4017 .
ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
Port Status 1c000004
ar7240-ehci ar7240-ehci.0: ATH EHCI
ar7240-ehci ar7240-ehci.0: new USB bus registered, assigned bus number 1
ehci_reset Intialize USB CONTROLLER in host mode: 3
ehci_reset Port Status 1c000000
ar7240-ehci ar7240-ehci.0: irq 3, io mem 0x1b000000
ehci_reset Intialize USB CONTROLLER in host mode: 3
ehci_reset Port Status 1c000000
ar7240-ehci ar7240-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
TCP cubic registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
ar7240wdt_init: Registering WDT success
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 112k freed
init started: BusyBox v1.01 (2012.08.01-03:58+0000) multi-call binary
This Board use 2.6.31
xt_time: kernel timezone is -0000
nf_conntrack version 0.5.0 (512 buckets, 5120 max)
ip_tables: (C) 2000-2006 Netfilter Core Team
insmod: cannot open module `/lib/modules/2.6.31/kernel/iptable_raw.ko’: No such file or directory
insmod: cannot open module `/lib/modules/2.6.31/kernel/flashid.ko’: No such file or directory
PPPoL2TP kernel driver, V1.0
PPTP driver version 0.8.3
insmod: cannot open module `/lib/modules/2.6.31/kernel/harmony.ko’: No such file or directory

Now flash open!
(none) mips #68 Tue Dec 4 11:19:54 CST 2012 (none)
(none) login: Now flash open!
ATHR_GMAC: Length per segment 1536
ATHR_GMAC: fifo cfg 3 01f00140
2
ATHR_GMAC: Max segments per packet : 1
ATHR_GMAC: Max tx descriptor count : 40
ATHR_GMAC: Max rx descriptor count : 96
ATHR_GMAC: Mac capability flags : 4D83
1
ATHR_GMAC: Max segments per packet : 1
ATHR_GMAC: Max tx descriptor count : 40
ATHR_GMAC: Max rx descriptor count : 252
ATHR_GMAC: Mac capability flags : 4403
athr_gmac_ring_alloc Allocated 640 at 0x81ea1800
athr_gmac_ring_alloc Allocated 4032 at 0x81d63000
Setting Drop CRC Errors, Pause Frames and Length Error frames
Setting PHY…mac 0
athr_gmac_ring_alloc Allocated 640 at 0x81ea1400
athr_gmac_ring_alloc Allocated 1536 at 0x81f2d000
athr_gmac_mii_setup: MDC check failed
Setting Drop CRC Errors, Pause Frames and Length Error frames
ATHRS26: resetting s26
ATHRS26: s26 reset done
Setting PHY…mac 1
device eth0 entered promiscuous mode
Now flash open!
nf_conntrack_rtsp v0.6.21 loading
nf_nat_rtsp v0.6.21 loading
asf: module license ‘Proprietary’ taints kernel.
Disabling lock debugging due to kernel taint
ath_hal: 0.9.17.1 (AR9380, DEBUG, REGOPS_FUNC, WRITE_EEPROM, 11D)
ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved
ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved
ath_ahb: 9.2.0_U5.508 (Atheros/multi-bss)
Boostrap clock 25MHz
ar9300RadioAttach: Need analog access recipe!!
Restoring Cal data from Flash
ath_get_caps[4735] rx chainmask mismatch actual 1 sc_chainmak 0
ath_get_caps[4710] tx chainmask mismatch actual 1 sc_chainmak 0
wifi0: Atheros 9380: mem=0xb8100000, irq=2
wlan_vap_create : enter. devhandle=0x80c942c0, opmode=IEEE80211_M_HOSTAP, flags=0x1
wlan_vap_create : exit. devhandle=0x80c942c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.
VAP device ath0 created

DES SSID SET=TP-LINK_EB07F2
ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1
WARNING: Fragmentation with HT mode NOT ALLOWED!!
device ath0 entered promiscuous mode
br0: port 2(ath0) entering forwarding state
ieee80211_ioctl_siwmode: imr.ifm_active=1442432, new mode=3, valid=1
br0: port 2(ath0) entering disabled state

DES SSID SET=TP-LINK_EB07F2
br0: port 2(ath0) entering forwarding state

TL-WR703N mips #68 Tue Dec 4 11:19:54 CST 2012 (none)
TL-WR703N login: ap71
BusyBox v1.01 (2012.08.01-03:58+0000) Built-in shell (msh)
Enter ‘help’ for a list of built-in commands.

$ cat /proc/version
Linux version 2.6.31–LSDK-9.2.0.312 (root@localhost.localdomain) (gcc version 4.3.3 (GCC) ) #68 Tue Dec 4 11:19:54 CST 2012
$ cat /proc/cpuinfo
system type : Atheros AR9330 (Hornet)
processor : 0
cpu model : MIPS 24Kc V7.4
BogoMIPS : 266.24
wait instruction : yes
microsecond timers : yes
tlb_entries : 16
extra interrupt vector : yes
hardware watchpoint : yes, count: 4, address/irw mask: [0x0000, 0x0200, 0x0020, 0x0248]
ASEs implemented : mips16
shadow register sets : 1
core : 0
VCED exceptions : not available
VCEI exceptions : not available

$ cat /proc/meminfo
MemTotal: 29992 kB
MemFree: 12076 kB
Buffers: 2144 kB
Cached: 6684 kB
SwapCached: 0 kB
Active: 3832 kB
Inactive: 6940 kB
Active(anon): 1944 kB
Inactive(anon): 0 kB
Active(file): 1888 kB
Inactive(file): 6940 kB
Unevictable: 0 kB
Mlocked: 0 kB
SwapTotal: 0 kB
SwapFree: 0 kB
Dirty: 0 kB
Writeback: 0 kB
AnonPages: 1968 kB
Mapped: 1824 kB
Slab: 4480 kB
SReclaimable: 328 kB
SUnreclaim: 4152 kB
PageTables: 188 kB
NFS_Unstable: 0 kB
Bounce: 0 kB
WritebackTmp: 0 kB
CommitLimit: 14996 kB
Committed_AS: 4820 kB
VmallocTotal: 1048404 kB
VmallocUsed: 2116 kB
VmallocChunk: 1037128 kB
$

可以看到TP官方的UBOOT认到了64M，但FLASH只认到4M，TP的固件还只认到32M的内存。果断刷不死UBOOT。刷完不死UBOOT后刷ART文件：https://blog.ich8.com/post/4045

刷的方法：https://blog.ich8.com/post/3933

直接刷不死UBOOT，64M 内存和8M FLASH都是被到了，TTL输出：

*****************************************
* U-Boot 1.1.4 (Jun 19 2013) *
*****************************************

AP121 (AR9331) U-Boot for TL-WR703N

DRAM: 64 MB
FLASH: Winbond W25Q64 (8 MB)

LED on during eth initialization…

Hit any key to stop autobooting: 0

Booting image at: 0x9F020000…
Uncompressing kernel image…
OK
Starting kernel…

[ 0.000000] Linux version 3.3.8 (v@v) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sun Jul 7 20:32:43 CST 2013
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9330 rev 1
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.000MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty – disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00004000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00004000
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: board=TL-WR703N console=ttyATH0,115200 rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 61588k/65536k available (2129k kernel code, 3948k reserved, 408k data, 208k init, 0k highmem)
[ 0.000000] SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop… 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.090000] gpiochip_add: registered GPIOs 0 to 29 on device: ath79
[ 0.100000] MIPS: machine is TP-LINK TL-WR703N v1
[ 0.550000] bio: create slab <bio-0> at 0
[ 0.560000] Switching to clocksource MIPS
[ 0.560000] NET: Registered protocol family 2
[ 0.570000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.570000] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.580000] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.580000] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.590000] TCP reno registered
[ 0.590000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.600000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.600000] NET: Registered protocol family 1
[ 0.630000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.630000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.640000] msgmni has been set to 120
[ 0.640000] io scheduler noop registered
[ 0.650000] io scheduler deadline registered (default)
[ 0.650000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.660000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UART
[ 0.670000] console [ttyATH0] enabled, bootconsole disabled
[ 0.670000] console [ttyATH0] enabled, bootconsole disabled
[ 0.680000] m25p80 spi0.0: found s25fl064k, expected m25p80
[ 0.680000] m25p80 spi0.0: s25fl064k (8192 Kbytes)
[ 0.690000] 5 tp-link partitions found on MTD device spi0.0
[ 0.690000] Creating 5 MTD partitions on “spi0.0”:
[ 0.700000] 0x000000000000-0x000000020000 : “u-boot”
[ 0.710000] 0x000000020000-0x000000103050 : “kernel”
[ 0.710000] mtd: partition “kernel” must either start or end on erase block boundary or be smaller than an erase block — forcing read-only
[ 0.720000] 0x000000103050-0x0000007f0000 : “rootfs”
[ 0.730000] mtd: partition “rootfs” must either start or end on erase block boundary or be smaller than an erase block — forcing read-only
[ 0.740000] mtd: partition “rootfs” set to be root filesystem
[ 0.750000] mtd: partition “rootfs_data” created automatically, ofs=4F0000, len=300000
[ 0.750000] 0x0000004f0000-0x0000007f0000 : “rootfs_data”
[ 0.760000] 0x0000007f0000-0x000000800000 : “art”
[ 0.770000] 0x000000020000-0x0000007f0000 : “firmware”
[ 0.790000] ag71xx_mdio: probed
[ 0.800000] eth0: Atheros AG71xx at 0xb9000000, irq 4
[ 1.350000] ag71xx ag71xx.0: eth0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd041, driver=Generic PHY]
[ 1.360000] eth1: Atheros AG71xx at 0xba000000, irq 5
[ 1.910000] eth1: Found an AR7240/AR9330 built-in switch
[ 2.950000] TCP cubic registered
[ 2.950000] NET: Registered protocol family 17
[ 2.950000] 8021q: 802.1Q VLAN Support v1.8
[ 2.960000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 2.970000] Freeing unused kernel memory: 208k freed
– preinit –
Press the [f] key and hit [enter] to enter failsafe mode
– regular preinit –
[ 8.490000] JFFS2 notice: (411) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 17 of xref (0 dead, 0 orphan) found.
[ 9.430000] SCSI subsystem initialized
[ 9.660000] usbcore: registered new interface driver usbfs
[ 9.660000] usbcore: registered new interface driver hub
[ 9.670000] usbcore: registered new device driver usb
[ 10.250000] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 10.260000] ehci-platform ehci-platform: Generic Platform EHCI Controller
[ 10.260000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 10.300000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 10.320000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 10.320000] hub 1-0:1.0: USB hub found
[ 10.320000] hub 1-0:1.0: 1 port detected
[ 10.440000] ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
[ 10.510000] Initializing USB Mass Storage driver…
[ 10.510000] usbcore: registered new interface driver usb-storage
[ 10.520000] USB Mass Storage support registered.
switching to jffs2
– init –

Please press Enter to activate this console. [ 33.250000] Compat-drivers backport release: compat-drivers-2013-01-21-1
[ 33.260000] Backport based on wireless-testing.git master-2013-02-22
[ 33.260000] compat.git: wireless-testing.git
[ 33.430000] cfg80211: Calling CRDA to update world regulatory domain
[ 33.440000] cfg80211: World regulatory domain updated:
[ 33.440000] cfg80211: (start_freq – end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 33.450000] cfg80211: (2402000 KHz – 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 33.460000] cfg80211: (2457000 KHz – 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 33.470000] cfg80211: (2474000 KHz – 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 33.470000] cfg80211: (5170000 KHz – 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 33.480000] cfg80211: (5735000 KHz – 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 34.420000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[ 34.420000] cfg80211: Calling CRDA for country: US
[ 34.430000] cfg80211: Regulatory domain changed to country: US
[ 34.430000] cfg80211: (start_freq – end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 34.440000] cfg80211: (2402000 KHz – 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
[ 34.450000] cfg80211: (5170000 KHz – 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
[ 34.460000] cfg80211: (5250000 KHz – 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 34.460000] cfg80211: (5490000 KHz – 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 34.470000] cfg80211: (5650000 KHz – 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 34.480000] cfg80211: (5735000 KHz – 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
[ 34.600000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[ 35.100000] PPP generic driver version 2.4.2
[ 35.140000] PPP MPPE Compression module registered
[ 35.270000] GRE over IPv4 demultiplexor driver
[ 35.290000] GRE over IPv4 tunneling driver
[ 35.520000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 35.770000] NET: Registered protocol family 24
[ 35.930000] nf_conntrack version 0.5.0 (965 buckets, 3860 max)
[ 36.380000] PPTP driver version 0.8.5
[ 36.920000] xt_time: kernel timezone is -0000
[ 37.470000] i2c /dev entries driver
[ 37.620000] usbcore: registered new interface driver ums-alauda
[ 37.650000] usbcore: registered new interface driver ums-cypress
[ 37.710000] usbcore: registered new interface driver ums-datafab
[ 37.740000] usbcore: registered new interface driver ums-freecom
[ 37.760000] usbcore: registered new interface driver ums-isd200
[ 37.780000] usbcore: registered new interface driver ums-jumpshot
[ 37.800000] usbcore: registered new interface driver ums-karma
[ 37.820000] usbcore: registered new interface driver ums-sddr09
[ 37.840000] usbcore: registered new interface driver ums-sddr55
[ 37.870000] usbcore: registered new interface driver ums-usbat
[ 38.000000] fuse init (API version 7.18)
[ 44.630000] device eth1 entered promiscuous mode
[ 47.930000] cfg80211: Calling CRDA for country: CN
[ 47.930000] cfg80211: Regulatory domain changed to country: CN
[ 47.940000] cfg80211: (start_freq – end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 47.950000] cfg80211: (2402000 KHz – 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 47.960000] cfg80211: (5735000 KHz – 5835000 KHz @ 40000 KHz), (N/A, 3000 mBm)
[ 50.040000] device wlan0 entered promiscuous mode
[ 50.080000] br-lan: port 2(wlan0) entered forwarding state
[ 50.090000] br-lan: port 2(wlan0) entered forwarding state
[ 52.090000] br-lan: port 2(wlan0) entered forwarding state
BusyBox v1.19.4 (2013-07-07 19:43:19 CST) built-in shell (ash)
Enter ‘help’ for a list of built-in commands.

_______ ________ __
| |.—–.—–.—–.| | | |.—-.| |_
| – || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
—————————————————–
ATTITUDE ADJUSTMENT (Attitude Adjustment, r37151)
—————————————————–
* 1/4 oz Vodka Pour all ingredients into mixing
* 1/4 oz Gin tin with ice, strain into glass.
* 1/4 oz Amaretto
* 1/4 oz Triple sec
* 1/4 oz Peach schnapps
* 1/4 oz Sour mix
* 1 splash Cranberry juice
—————————————————–
root@Navigator:/# ifconfig
br-lan Link encap:Ethernet HWaddr 6C:E8:73:D2:89:C9
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:50 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:6788 (6.6 KiB)

eth0 Link encap:Ethernet HWaddr 6C:E8:73:D2:89:C8
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:4

eth1 Link encap:Ethernet HWaddr 6C:E8:73:D2:89:C9
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:5

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:336 errors:0 dropped:0 overruns:0 frame:0
TX packets:336 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:22848 (22.3 KiB) TX bytes:22848 (22.3 KiB)

wlan0 Link encap:Ethernet HWaddr 6C:E8:73:D2:89:C8
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:50 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:7688 (7.5 KiB)

root@Navigator:/#