当前位置: 首页 > 无线与硬件 > 正文

T2UeJ1XjJcXXXXXXXX_!!203979744

U-Boot 1.1.3 (Dec 10 2011 – 15:58:15)

Board: Ralink APSoC DRAM: 64 MB
relocate_code Pointer at: 83fb0000
spi_wait_nsec: 3c
spi device id: c2 20 16 c2 20 (2016c220)
find flash: MX25L3205D
raspi_read: from:30000 len:1000
.*** Warning – bad CRC, using default environment

initGpio pin 9 to on the power LED and ping 12 to reset Gga phy
============================================
Ralink UBoot Version: 3.5.3.0
——————————————–
ASIC 3352_MP (Port5<->None)
DRAM_CONF_FROM: Boot-Strapping
DRAM_TYPE: DDR2
DRAM_SIZE: 512 Mbits
DRAM_WIDTH: 16 bits
DRAM_TOTAL_WIDTH: 16 bits
TOTAL_MEMORY_SIZE: 64 MBytes
Flash component: SPI Flash
Date:Dec 10 2011 Time:15:58:15
============================================
icache: sets:256, ways:4, linesz:32 ,total:32768
dcache: sets:128, ways:4, linesz:32 ,total:16384

##### The CPU freq = 400 MHZ ####
estimate memory size =64 Mbytes
raspi_read: from:bc020000 len:10000
.## Starting application at 0x81E00000 …

Z-LOADER V1.04 | 12/10/2011 15:58:19

raspi_read: from:bc04fe00 len:200
.raspi_read: from:bc04fe00 len:200
.raspi_read: from:40028 len:6
.
Hit ESC key to stop autoboot: 0
NetTxPacket = 0x83FE4CC0
Trying Eth0 (10/100-M)

Waitting for RX_DMA_BUSY status Start… done

Header Payload scatter function is Disable !!
===>ETH_STATE_ACTIVE!!
Trying Eth0 (10/100-M)
===>ETH_STATE_ACTIVE!!

wait multiboot… 0
raspi_read: from:50000 len:40
.Check image validation:raspi_read: from:50040 len:2887f7
………………………………….. OK
## Booting image at bc050000 …
raspi_read: from:50000 len:40
. Image Name: 1.10(VDA.2)b1_12A
Created: 2011-12-10 7:58:11 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 2656247 Bytes = 2.5 MB
Load Address: 80000000
Entry Point: 80331000
raspi_read: from:50040 len:2887f7
………………………………….. Verifying Checksum … OK
Uncompressing Kernel Image … OK
No initrd
## Transferring control to Linux (at address 80331000) …
## Giving linux memsize in MB, 64

Starting kernel …

LINUX started…

THIS IS ASIC

硬件配置:
CPU:Ralink RT3352F 400MHz MIPS 24Kc
内存:Winbond 64M DDR2
FLASH:4M SPI Flash

[分享]华勤WAP120NF 802.11n 300Mbps AP TTL输出信息:目前有 7 条评论

  1. 4楼
    gavinguang

    接上TTL之后,usb上只亮一个灯,板子通电后也只有无线灯闪烁,超级终端连上后白屏无反应,请教霸王这是怎么回事

  2. 地板
    gavinguang

    波特率选错了..汗
    谢谢霸王兄

  3. 板凳
    sgzj01

    你好,我也一样,接上TTL之后,usb上只亮一个灯,板子通电后也只有无线灯闪烁,超级终端连上后白屏无反应,波特率是多少?

  4. 沙发
    sgzj01

    想从官方刷到雷凌的,直接就悲剧了,开机就就电源灯亮,接上TTL线,板子就无线灯闪,TTL读不到信息

发表评论